Random
Source Code
Random
like a gun it is a weapon that fires a bullet with explosive pressure out of a barrel, typically using a trigger system.
the differences from a regular firearm is how it is made, and what it is made from.
like snowflakes they are always different, with different metals and inconsistent design.
they usually are single shot reloadables, have simple designs, and are unsafe.
sometimes they are inspired and built from parts of other weapons like the ak-47.
police officer 1: we found a stockpile of improvised firearms during a raid?
officer 2: are they functional?
officer 1: no they are not.
When you spread athletic muscle cream (such as Icy Hot) all of your arm and hand and then fist someone. A sub word or phrase if this would be Fire in the hole. This is when you put your muscle creamed arm in the poop shoot instead of the vagina.
I am about to issue you a firearm. Look out fire in the hole.
When you get caught having illegal firearms
Usually to prevent yourself from getting fucked
1: what did John do to get arrested?
2: possession of illegal firearms
1: ok
3d gunner youtube
Gorilla glue and sawdust can be used to create a molded part that is strong and durable. Here is how you can make a molded part using Gorilla glue and sawdust:
Materials:
- Gorilla Glue
- Sawdust
- Mixing bowl
- Measuring cup
- Mixing spoon or spatula
- Mold or form
- Sandpaper
Instructions:
1. Mix the Gorilla Glue and sawdust together in a mixing bowl. Start with a ratio of 1:1, and adjust as needed to achieve the desired consistency. The mixture should be thick and moldable, but not too dry or too wet.
2. Press the mixture into the mold or form, making sure to pack it tightly and evenly. Smooth out the surface as much as possible.
3. Let the mixture dry for at least 24 hours, or until it is completely hardened.
4. Remove the molded part from the mold or form. If necessary, use a knife or other tool to carefully pry it loose.
5. Sand the surface of the molded part with sandpaper to remove any rough or uneven spots. You can also use sandpaper to shape and refine the part as needed.
6. Your molded part is now ready to use! It can be painted or finished as desired.
even substitue the sawdust for your drywall if ground with morter and pestol glue sticks work if mixed with alcohol.
Part 3
3d youtube firearm 3
Ammunition for 3d youtube firearm 1,2,3
Gunpowder, also known as black powder, is a mixture of three main ingredients: potassium nitrate (also known as saltpeter), charcoal, and sulfur. The ingredients are mixed together in specific proportions and then ground into a fine powder.
The traditional formula for gunpowder is 75% saltpeter, 15% charcoal, and 10% sulfur by weight. However, the proportions can vary depending on the desired properties of the powder.
To mix the ingredients, they are typically pulverized separately and then combined in a mixing bowl or mortar and pestle. The mixture is then ground and blended thoroughly until it forms a homogenous powder.
It is important to note that creating gunpowder can be dangerous and requires specialized knowledge, equipment, and permits. It is not recommended for individuals without proper training and experience to attempt to make their own gunpowder.
Part 6
3d youtube firearm 6
Ammunition for 3d youtube firearm 1,2,3
Materials:
- Heavy paper (such as cardstock or construction paper)
- Scissors
- Ruler
- Pen or pencil
- Glue or tape
- Shotshell crimping tool (optional)
Instructions:
1. Cut a rectangular piece of heavy paper that is approximately 4 inches long and 2 inches wide. This will be the body of the shell.
2. Fold the paper in half lengthwise, creasing it firmly. This will create a center line down the length of the paper.
3. Open the paper back up and draw a line across the center line, approximately 1/2 inch from one end of the paper. This will mark where the base of the shotshell will be.
4. Draw a line lengthwise down the center of the paper, starting at the base line and ending about 1/2 inch from the opposite end of the paper.
5. Fold the paper in half again along the center line, pressing firmly to create a sharp crease.
6. Fold the bottom end of the paper up along the base line, creating a bottom flap that is approximately 1/2 inch long.
7. Apply glue or tape to the top edge of the bottom flap, and press the two sides of the paper together to form a tube. Hold the paper in place until the glue or tape dries.
8. Fill the tube with the desired amount of shot.
9. Cut a circular piece of paper that is slightly larger in diameter than the open end of the tube. This will be the top wad.
10. Place the top wad over the open end of the tube, and press it down firmly to create a seal.
Part 5
3d youtube firearm 5